SHUTTLE DS20U7 fanless 65W 2

XPC slim DS20U7

• Intel Core i7-10510U (up to 4.90 GHz, 4 cores, 8 threads, 8 MB cache)
• Intel UHD Graphics
• Up to 64 GB of DDR4 memory
• 1× NVMe, 1× SATA 2.5", card reader
• 1× HDMI 2.0b, 1× DisplayPort 1.2, 1× VGA
• Two M.2 slots (1× M.2-2280, 1× M.2-2230)
• 2× Gigabit Ethernet, WLAN-ready, 4G-ready
• 4× USB 3.2 Gen 2 (10 Gbit), 4× USB 2.0, 1× COM
• Remote power-on connector, always-on jumper
• Wall/VESA mount included
• Optional DIN-Rail/19” mount

• Passive cooling, no fan noise at all
• Perfect to be used in noise-sensitive environments
• Fanless, dust-free and thus virtually maintenance-free

• Power consumption in idle mode with 2.5" SSD under Windows 10: ca. 6 W only

• This device is approved for 24/7 permanent operation.
• Requirements:
  • Free circulation of air amongst the PC must be guaranteed.
  • Ventilation holes must stay clear.
  • If a hard disk is installed, this must also be approved for permanent operation by its manufacturer

• Slim-PC with black steel chassis
• Without cooling fan, passive cooling only
• The bays for memory, 2.5" drive and M.2 card
• can easily be accessed by removing two cover plates.
• Dimensions: 200 x 165 x 39.5 mm (LWH) = 1.3 litres
• Weight: 1.5 kg net and 2.2 kg gross
• Two holes for Kensington Lock and numerous threaded holes (M3) at both sides of the chassis

1. Vertical: Usual operating position with the supplied feet (DisplayPort output facing up).
2. VESA-mounted: The device can also be mounted behind an appropriate monitor using the supplied VESA mount kit.
   Note: From a thermal point of view horizontal operation is permitted. However, there are no rubber feet on the device. The maximum operating temperature is 35 °C then.

• This barebone system comes without operating system.
• It is compatible with Windows 10/11 (64-bit) and Linux (64-bit).

• Model: Intel Core i7-10510U (ULV)
• System-on-a-chip architecture (SoC) with integrated memory and graphics controller
• FCBGA1528 package - directly soldered onto the mainboard
• Code name: Comet Lake U (10th Generation Intel Core)
• Cores / Threads: 4 / 8
• Base frequency: 1.8 GHz
• Max. Turbo frequency: 4.9 GHz
• Intel Smart Cache: 8 MB
• TDP wattage: 15 W maximum
• Manufacturing process: 14nm
• Maximum Tjunction Temperature: 100 °C
• Supports 64-bit, VT-x (EPT), VT-d, Enhanced SpeedStep, NX bit, AES-NI, SSE 4.1/4.2

• Intel UHD Graphics
• GPU clock frequency: 300~1150 MHz
• Execution Units (EUs): 24
• Supports DirectX 12, OpenGL 4.5
• Supports full H264, H265 8/10 bit, VP8/9, VC-1, AVC hardware decoding
• Supports Quick Sync Video and Clear Video HD technology
• Supports up to three independent screens:
  1. DisplayPort 1.2 supports Ultra HD @ 60 Hz
  2. HDMI 2.0a supports Ultra HD @ 60 Hz
  3. D-Sub/VGA supports analog displays

• Shuttle Mainboard FS20
• All capacitors are high quality solid capacitors
• Supports resume after power failure
• Supports Wake on LAN (WOL)
• Supports Power on by RTC Alarm
• Supports boot from M.2 SSD cards und USB devices
• AMI BIOS in 16 MByte EEPROM with SPI interface
• Supports hardware monitoring and Watchdog function
• Supports Unified Extensible Firmware Interface (UEFI)
• Supports Firmware-TPM (fTPM) Version 2.0

• External 65 W power adapter (fanless)
• Input: 100~240 V AC, 50/60 Hz, max. 1.6 A
• Output: 19 V DC, max. 3.42 A, max. 65 W
• DC cable length: ca. 170 cm
• AC cable length: ca. 170 cm (3-pin Micky MM C6 and Schuko earthed safety plug)

• DC Input Connector: 5.5 / 2.5 mm (outer/inner diameter)
• The DC-input of the computer supports an external
• power source with either 12V±5% or 19V±5%.

• 2x SO-DIMM slot with 260 pins
• Supports DDR4-2666 (PC4-21300) SDRAM at 1.2 V
• Supports DDR4-3200 at 2666 MHz
• Supports Dual Channel mode
• Supports a maximum of 32 GB per DIMM,
• maximum total size: 64 GB
• Supports two unbuffered DIMM modules (no ECC or registered)

• Supports one Serial ATA hard disk
• or one SATA SSD drive in 6.35 cm / 2.5" format
• Device height: max. 12.5 mm
• Supports Serial-ATA III, 6 Gb/s (600 MB/s) bandwidth
• Supports Unified Extensible Firmware Interface (UEFI)
• Note: no Serial ATA cable is required.

• The M.2 2280 BM slot provides the following interfaces:
  • PCI-Express Gen. 3.0 X4
  • SATA v3.0 (max. 6 Gbps)
• It supports M.2 cards with a width of 22 mm
• and a length of 42, 60 or 80 mm (type 2242, 2260, 2280).
• Supports M.2 SATA SSDs (with B+M key) and M.2 PCIe NVMe SSDs (with M key)

• Interfaces: PCI-Express Gen. 2.0 X1 und USB 2.0
• Supports M.2 cards with a width of 22 mm and a length of 30 mm (type 2230)
• Supports WLAN expansion cards (optional Shuttle accessory: WLN-M)
• 2x pre-installed antenna cables

• Integrated SD card reader
• Supports SD, SDHC and SDXC memory flash cards

• Audio Realtek® ALC897 or ALC 662 High-Definition Audio
• Two analog audio connectors (3.5 mm) at the front panel:
  1. 2 channel line out (headphones)
  2. microphone input
• Digital multi-channel audio output: via HDMI and DisplayPort

• Dual network with two RJ45 ports
• Used network chips:
  1. Intel i211 Ethernet Controller with MAC, PHY and PCIe interface
  2. Intel i219LM PHY connected to the MAC of the processor
• Supports 10 / 100 / 1.000 MBit/s operation
• Supports WAKE ON LAN (WOL)
• Supports network boot by Preboot eXecution Environment (PXE)
• Supports Teaming mode

• 2x pre-installed antenna cables (WLAN card and antennas not included)
• Prepared for the installation of an M.2-2242 WLAN card and two external antennas

• 2x USB 3.2 Gen 2 (red, max. 10 Gbps)
• 4x USB 2.0
• Microphone input
• Audio Line-out (headphones)
• SD card reader (supports SD, SDHC, SDXC)
• Power button
• Power LED (blue)
• HDD LED (yellow)

• DisplayPort 1.2
• HDMI 2.0a
• D-Sub/VGA
• 2x USB 3.2 Gen 2 (red, max. 10 Gbps)
• 2x Intel Gigabit LAN (RJ45)
• Serial COM port (5V / 12V, switchable to RS232 / RS422 / RS485)
• DC-input connector for external power adapter
• 4-pin connector (2.54 mm pitch) for power button, Clear CMOS and 5 V DC

• By removing Jumper J9 (please refer to the quick user guide),
• the system will start unconditionally once power is applied

• Multi-language user guide
• Two metal feet with four screws M3 x 7 mm
• VESA mount for 75/100mm standard (two metal brackets)
• Four screws M3 x 7 mm (screws together VESA mount and PC)
• Four screws M4 x 10 mm (to fix the VESA mount to the external surface)
• Two screws M3 x 5 mm to mount a 2.5" storage in the bay
• Two screws M3 x 5 mm to mount M.2 cards
• Driver DVD for Windows
• External 65W power adapter with power cord (with protective-earth contacts)

• PCP11: adapter cable for the second COM port (replaces the VGA port)
• CXP01: adapter cable for external power button
• WWN03: LTE adapter kit for the 2.5" bay including two external LTE antennas
• WLN-M: WLAN module (802.11ac + BT) with two external antennas and cables
• PRM01: 2U rack mount front plate for two Shuttle XPC slim
• DIR01: mounting kit for 35 mm DIN-Rail

• Operating temperature range: 0~40 °C
• Relative humidity, non-condensing: 10~90 %

• EMI: CE, FCC, BSMI, RCM, VCCI
• Safety: CB, BSMI, cTUVus
• Other: RoHS, Energy Star, ErP
• This device is classed as a technical information equipment (ITE) in class B and is intended for use in living room and office. The CE-mark approves the conformity by the EU directives:
  • (1) 2014/30/EU relating to electromagnetic compatibility (EMC)
  • (2) 2014/35/EU relating to Electrical Equipment designed for use within certain voltage limits (LVD)
  • (3) 2009/125/EC relating to eco design requirements for energy-related products (ErP)